how to take links out of a citizen watch

If is often necessary to use a 10x Head Visor and Blocks to hold the Watch down as you work on it. Find the small opening on the side of the first link you want to remove.

Citizen Eco Drive Proximity Stainlesssteel Watch No Scratches On The Face Some Minor Scratches On The Links S Mens Accessories Jewelry Citizen Eco Eco Drive

Repeat Step 1 on the other end of the links.

. Locate the Link Pins. Purchase a Citizen Watch Band Sizing Tool CIT-SZTOOL from a Citizen Watch dealer or online. Watch Hammer one with a head with a soft side and a metal side Watch band block holder. Line up one of the pinholes with the CIT-SZTOOL sizing pin.

Once you remove the pins or screws the link is loose. Line up the pin hole with the side of the bracelet using the Citizen sizing pin. Remove the pins from each link using a pin removal tool a watch screwdriver or needle nose pliers. Locate the pins on the watchband links.

Grab the portion of the pin thats sticking out with a pair of. Place the watch bracelet in the holder so the arrows are pointing downward. That means in most cases you will have to pry up on 4 tabs for each side of the watch band to remove one link. In order to remove links from your Michael Kors watch you will first need the right tools.

Apply gentle pressure to the pin pushing it out as far as the CIT-SZTOOL allows. To remove a link in your watch band you must first locate where to remove the link and. Use your fingers or a small pair of tweezers to completely remove the pin from the link. Pry up on 2 tabs next to each other on most bands there will be tabs on the inside of the watch band and the outside.

Slide a pushpin into the opening of that link until the pin holding the band in place sticks out of the other side. You may need to tap the back of the pushpin with a rubber mallet or small hammer. Proper bracelet sizing requires special expertise and experience. Pull the small U shaped clips out of both links of the band.

There will be an arrow mark on the underside of the concatenation. How to Remove Watch link with Snap Type Pins. Then take your watch off and lay it flat. How to Remove Watch Links Step 1.

And every Watch is Different. Push the pin out of the link slowly using the sizing pin. Remove the the small piece --. Steps to separate snap pins.

Citizen Eco-drive watch. Place the watch band bracelet into the CIT-SZTOOL with the arrows pointing away from you. They all Require Different Tools Pin Pushers Pliers Devices to get those Pins out. This is done using a paper clip and a hammer to carefully remove the pins that retain th.

Store the removed pins or screws in a safe place. Using a straight motion pull the rest of the pin completely. Bring the point of the push-pin tool to the pin and lightly tap against the tool with the flat end of the ball-peen hammer until you can no longer push the pin inside the link. If the shaft does not have the arrow mark which means you cannot remove that concatenation.

Proceed to gently punch out the pin as far as it will go and then use your fingers or tweezers to completely remove it. Figure Out How Many Links to Remove for the Correct Fit. Stretch the band a few times and you will see a small connecting piece between the upper link and lower link. To separate snap pins is very easy.

Identify the type of pins in the links--friction split or straight. To learn How to Determine How Many Links to Remove from your watch band check out this article. Pry the edge of the band up to get to the small connecting piece. Turn the watch on its side find the link you wish to remove and locate the.

Any links removed from your watch will be returned with the order should you need to have it adjusted. Reassemble the watchband once you have achieved the correct size. Use a 1mm screwdriver to remove the required screw. You can do this by applying light pressure and.

Here Are the Tools I Used. Count the number of links you need to remove from this side of the watch band. Once the pin is pulled out the link should come apart. Use a pin pusher or paper clip to remove pins from each link you wish to remove.

Place your Eco Drive watch into the CIT-SZTOOL. Pin Punch for watch pins. Place the watch band in the watch holder and align the hole in the last. Some Watches take 2 Minutes to Operate on others take 12 Hour.

Lay the watch on a clean flat surface that will not scar its face. Remove the First Pin. This is a picture of two links together. Take out the pin of the clinch you want to remove by using the pin pusher tool.

Remove links evenly from both sides of the band to ensure symmetry. If you have push pins which are the most common pins in your watch links versus screws which require a jewelers precision. Its easy to use painless and takes just a couple of seconds to line up the link and push the pin through by screwing the pin pusher through the device. Most watches will have up to three pins that may be removed on each.

Identify the link you wish to remove. Continue applying pressure to the sleeve until it falls out of the link. This small plastic device is something every jeweler has. Adding and removing links to size the band.

If you did not opt for the free sizing at the time of purchase we kindly recommend visiting a local jeweler nearest you to have your watch adjusted to your preferred wrist size. Watch Band Link Remover. What the Customers Fail to see is that we are Trained at Removing Links. Lay the watchband upside down on a hard surface.

How to Remove Watch Band Links on a Citizen Stiletto Eco-Drive Watch Step 1. Be on the lookout for any small metal ferrules that might have fallen out and place those and the pins. Removing Links with Screwed Pins 1.